BPT 2010 high-speed industrial 3D printer
A large-scale industrial 3D printer that produces parts up to two metres long as a single body, at print speeds of up to 1000 mm/s. It is equipped with a 450 °C nozzle and a chamber heated up to 170 °C for high-performance polymers such as PEEK and ULTEM / PEI. The model name derives from its build volume: 2000 × 1000 × 1000 mm.
- 2000 × 1000 × 1000 mm
- 1000 mm/s while printing
- 1 µm resolution
- Bed 180 °C · Chamber 170 °C
- 380 V three-phase
Industrial scale
2 m³ of build volume, one-piece parts.
The 2000 × 1000 × 1000 mm working area of the BPT 2010 allows components larger than desktop and cabinet-type systems can accommodate to be produced without splitting. The system is designed for continuous production, with servo-driven axes, an industrial electrical cabinet and 380 V three-phase supply.
- Build volume
- 2000 × 1000 × 1000 mm (2 m³)
- Power supply
- 380 V three-phase
- Motion system
- Linear servo-driven X/Y, servo-driven Z
- Chamber
- Controlled environment up to 170 °C
Speed and throughput
High speed, closed-loop accuracy.
On the BPT 2010, the X and Y axes are driven by linear servo motors. Speeds of up to 1000 mm/s are reached while printing, and up to 2000 mm/s on non-printing moves between layers and print regions. Closed-loop feedback at 1 µm resolution on the axis motors monitors position continuously at these speeds, so speed is not gained at the expense of dimensional consistency.
On large parts, the number of layers also governs total job time. The 0.2 – 1 mm layer height range allows fine layers where surface requirements are high and thick layers on bulky parts. Actual print speed depends on the material, geometry and layer settings.
- Print speed
- Up to 1000 mm/s
- Travel speed
- Up to 2000 mm/s
- X / Y drive
- Linear servo motor
- Position control
- 1 µm resolution, closed-loop feedback
- Nozzle diameter
- 0.4 – 1.2 mm
- Layer height
- 0.2 – 1 mm
- Material capacity
- 5 kg per head, two independent heads
- Continuity
- Filament sensor; resumes where it stopped after a power cut
Key features
Dimensional consistency across a large volume.
-
Independent dual extruder
Two independent print heads with 5 kg capacity each print model and support material from separate heads within the same job cycle. No head change is needed for material transitions.
-
1 µm positioning resolution
Closed-loop feedback with 1-micron resolution on the axis motors limits cumulative position error over long axis travel and preserves repeatability across a large volume.
-
PEEK-coated heated bed
Multi-zone heating up to 180 °C reduces temperature differences across a large surface, stabilises first-layer adhesion and lowers the risk of warping in engineering polymers.
-
Laser bed scanning
Automatic bed calibration by non-contact laser scanning and automatic nozzle offset measurement with a touch probe; first-layer height does not depend on the operator.
-
Industrial control interface
21" touchscreen, role-based access (Operator / Administrator), live production status and temperature visualisation.
-
Industrial safety system
A dual-channel safety relay, a hardware emergency stop (E-Stop) wired to all servo drives, a software-monitored door sensor and a Z-axis holding brake are standard.
Technical specifications
BPT 2010 data sheet
Build volume
- Working area
- X 2000 mm × Y 1000 mm × Z 1000 mm
- Machine dimensions
- 3500 × 2200 × 2500 mm (L × W × H)
- Machine weight
- 2000 – 2500 kg (varies with the selected equipment)
Motion system
- X / Y axes
- Linear servo motor drive; 2000 mm/s travel, 1000 mm/s while printing
- Z axis
- Servo motor drive with ball screw
- Positioning accuracy
- Closed-loop feedback with 1-micron resolution on the axis motors
- Synchronisation
- X/Y axes move together; Z axis moves independently
Heated bed and chamber
- Bed surface
- PEEK-coated, industrial multi-zone heating
- Bed temperature
- 180 °C
- Chamber temperature
- Controlled environment up to 170 °C
- Temperature sensing
- Multi-point precision sensors, zone control
Extruder system
- Configuration
- Independent dual extruder heads, 5 kg each
- Materials
- Dual-material printing with model + support material
- Nozzle diameter
- 0.4 – 1.2 mm
- Layer height
- 0.2 – 1 mm
- Maximum nozzle temperature
- 450 °C
- Nozzle calibration
- Automatic nozzle offset measurement with touch probe
- Fibre-filled
- PA-CF, PEEK-CF etc.; wear-resistant nozzle
Control and interface
- Display
- 21" industrial touchscreen
- Usability
- Intuitive, operator-friendly interface; role-based access (Operator / Administrator)
- Process visibility
- Live production status and temperature visualisation
- Bed scanning
- Automatic bed-plane calibration by non-contact laser scanning
- Filament sensor
- Stops the print when filament runs out or breaks
- Power-loss recovery
- Printing resumes where it stopped after a power cut
Safety systems
- Safety relay
- Dual-channel industrial safety relay; hardware emergency stop (E-Stop) wired to all servo drives
- Door safety
- Software-monitored door sensor; automatic park move when opened
- Z-axis lock
- Electromagnetic holding brake
Electrical and power
- Power supply
- 380 V three-phase
- Power requirement
- 15 – 23 kW (varies with the selected equipment)
- Cabinet
- Industrial electrical cabinet, three-phase load balancing
- Wiring
- Compliant with international colour-coding standards
Materials
From standard filaments to high-performance polymers.
The BPT 2010 processes a wide range of materials, from standard filaments to high-performance engineering polymers such as PEEK and ULTEM. A nozzle temperature of up to 450 °C, a chamber controlled up to 170 °C and a PEEK-coated bed heated up to 180 °C provide the thermal environment these materials require.
Standard
- PLA
- ABS
- ASA
- PA / Nylon
- PC
High performance
- PEEK
- PEKK
- PPS
- PPSU
- ULTEM / PEI
Fibre-filled
- PA-CF
- PEEK-CF
- Glass-fibre filled
Fibre-filled materials are printed with a wear-resistant nozzle. Details: 3D printing materials · PEEK 3D printing

Request a quote for the BPT 2010.
Share the parts you intend to produce and your operating conditions. We will prepare a quote covering installation, training and service.